리튬 배터리 전압은 어떤 전압 창을 가져야 하나요: 30.2V 충전에서 21V 차단 설명

리튬 배터리 전압은 어떤 전압 창을 가져야 하나요: 30.2V 충전에서 21V 차단 설명



What voltage window should a lithium-ion pack have?

The window is set by the cell count and by the chemistry's safe operating limits, and on a pack it reads as follows: it charges up to 30.2V, delivers a nominal 25.9V in the middle of its range, and stops discharging at 21V. The three figures are not interchangeable and they are not alternatives — they are the top, the middle and the bottom of one continuous scale.

엔지니어들은 때때로 액추에이터가 신경 쓰는 명목 수치만 지정하기도 합니다. 액추에이터는 명목상 등급을 중요하게 생각하지만, 보호 위원회는 두 가지 끝을 중요하게 생각하며, 이 두 끝이 팩이 2년을 버틸지 아니면 첫 해에 스스로 차단될지를 결정합니다. 세 줄을 모두 쓰고, 단위와 방향을 함께 쓰세요: 최대값, 최소값, 명목값 등.

왜 충전 상한선이 30.2V로 설정되어 있나요?

최대 충전 전압은 충전 회로가 종료되어야 하는 수준입니다. 그 이상으로 충전하면 팩이 설계된 충전 조건을 벗어나게 되고, 계속 충전하면 셀에 스트레스를 주어 수명이 단축되고, 최악의 경우 성능 불만이 아닌 안전 문제를 일으킬 수 있습니다.

명세에 대한 두 가지 결과가 따릅니다:

  • 천장은 충전기가 아니라 팩의 것입니다. A charger is a lithium battery voltage source; the limit is a pack-level threshold. Specify both, and state that the protection circuit terminates charge at 30.2V independently of what the charger is doing. Where the limit exists only in the charger, a single wrong charger model in the field removes the protection entirely.
  • 상한선은 명확한 수치이지 목표가 아닙니다. Writing "approximately 30V" or "29–30V" in a specification creates ambiguity about which component enforces the limit and at what value. State 30.2V, state which layer enforces it, and state what the pack does when the threshold is reached.

Note the relationship with the paired charger: its output is 29V, which sits below the 30.2V ceiling. That is the intended architecture — the charger operates inside the window and the protection circuit enforces the boundary.

왜 21V가 방전 종료 제한인가요?

방전 차단은 팩이 에너지 공급을 멈추는 지점입니다. 너무 낮게 설정하면 세포가 원래 회복할 수 없는 상태로 몰려들게 됩니다; 너무 높게 설정하면 사용 가능한 용량이 미주인공이 됩니다. 이 팩의 수치는 최소 21V이며, "최소"라는 단어는 실제 작업을 하고 있습니다: 즉, 팩이 그 이하로 방전되어서는 안 된다는 의미이지, 평소에 그 수준에서 작동한다는 의미는 아닙니다.

깊은 방전은 나중에 충전을 거부하는 팩의 가장 흔한 근본 원인입니다. 고장은 방전 순간에 나타나지 않습니다; 몇 주 후, 사용자가 의자가 작동하지 않고 팩도 충전되지 않는다고 보고할 때 나타납니다. 이 진단 경로 때문에 컷오프 값과, 특히 컷오프 이후의 복구 동작이 명세서에 명세서에 포함되어야 합니다. 명시된 복구 경로 없이 컷오프는 사양의 절반에 불과합니다.

There is also a practical point about where the cut-off is evaluated. A pack's terminal voltage falls under load, so a cut-off assessed at rest and a cut-off assessed while the motor is running can behave differently in the field. State the load condition under which the threshold is defined.

충전기는 팩 창문에 대해 어떻게 놓여야 하나요?

Specify the window first, then buy the charger to match it — never the other way round. Three lines have to agree, and they have to agree in writing:

  • 팩 충전 전압 제한: 최대 30.2V, 보호 회로에 의해 강제됩니다.
  • 팩 요금 전류 수용: 0.6A nominal and 1A maximum. A charger with a higher current rating does not push more energy into the pack than the pack's charging circuit accepts; the excess rating is simply unused, and any mismatch it creates appears somewhere less visible in the system.
  • 충전기 출력: 29V 2A, with a 1.2m mains cable where a cable is supplied. State the charger's output voltage and current next to the pack's limits so the pairing is unambiguous.

연락하세요


추천